Application: On-site repair of marine engines
Marine engines are designed for long service lives. Nevertheless, cavitation damage, worn bearing seats or localized material loss can require extensive repairs. For large, permanently installed engines and their components, dismantling, transportation and reinstallation in particular can result in considerable costs and downtime.
OSCAR PLT GmbH develops mobile repair solutions that allow suitable damaged areas to be restored directly on installed components. The technology is based on laser wire directed energy deposition (DED). ProFocus technology enables precise material deposition even in confined spaces, such as the engine room of a ship.
Typical repair applications for marine engines
Repairing localized cavitation damage
Cavitation can cause localized but critical material damage to engine components. Whether a repair is feasible depends, among other factors, on the depth of the damage, the base material and the function of the affected surface.
Where conditions are suitable, the damaged area is prepared and rebuilt through targeted material deposition. The filler material and welding strategy are adapted to the specific application. The underlying cause of the damage must also be considered, as material deposition alone does not eliminate the conditions that cause cavitation.
Restoring worn bearing seats
Wear on bearing seats can prevent the required dimensions and fits from being maintained. Instead of replacing the entire component, localized repair may offer an economically viable alternative.
During laser deposition, material is applied to the prepared damaged area. The required final geometry and surface quality are then achieved through machining. Suitable material combinations and sufficient accessibility of the repair area are essential prerequisites.
Repairing marine engines directly on board: Practical project with Wärtsilä and SKM
|
In collaboration with Wärtsilä, the mobile ProFocus technology has already been used on two test engine blocks and in two actual on-site repairs aboard ships. Solid welding wires were used, in some cases on cast base materials. These projects demonstrate the practical feasibility of the repair strategy and its acceptance in real-world applications. A particular benefit for the customer was the ability to carry out repairs directly at the operating location, in some cases while the vessel was underway, avoiding extensive dismantling procedures. |
|
Digital repair planning in collaboration with S.K.M. Informatik
During a documented repair operation for Wärtsilä, OSCAR PLT GmbH collaborated with its technology partner S.K.M. Informatik GmbH. While OSCAR PLT contributed its ProFocus welding technology and welding process expertise, SKM used its SKM DCAM software to support spatial feasibility assessment, robot positioning, toolpath planning and simulation.
|
For the repair planning, the actual spatial conditions in the engine room were captured using a smartphone-based LiDAR scan. This data made it possible to digitally assess different robot positions, tool orientations and the accessibility of the areas requiring repair. As a result, the robot setup could be prepared in advance and adapted to the available space. |
|
During the documented on-site repair, the robot and welding head were positioned directly at the cylinder openings of the installed engine block. The project images show the equipment setup at the component as well as the machined annular areas. The project demonstrates how digital planning and mobile welding technology can work together to address demanding repair tasks. |
|
ProFocus Compact as the basis for mobile repair systems
The ProFocus Compact is among the most compact and lightweight laser wire DED heads on the market. For mobile repair applications, it can be combined with suitable motion or robotic systems. Wire feeding, hose assemblies and process control are adapted to the specific application.
Controlled material deposition on challenging materials
For cast materials in particular, material composition, component condition and thermal conditions are critical to a successful repair. ProFocus technology enables localized and precisely controlled heat input. Penetration depth and dilution can be influenced through process control and must be adapted to the specific material combination.
The appropriate welding strategy is determined based on the specific damage. This includes selecting the filler material, preparing the surface, defining process parameters and, where necessary, implementing thermal measures. Further technical information is available on our knowledge page about laser wire directed energy deposition.
Is your engine component suitable for repair?
The following questions are particularly relevant for an initial technical assessment:
| • | Which component is damaged, and what function does the affected surface perform? |
| • | What type and depth of damage are present, and which base materials are involved? |
| • | Which dimensions, tolerances and surface requirements must be achieved? |
| • | How accessible is the repair area, and which preparation and finishing operations can be carried out on site? |
| • | Is this a one-off repair or a recurring maintenance requirement? |
OSCAR PLT GmbH assesses the damage, material and accessibility to determine whether mobile repair using laser wire directed energy deposition is technically feasible. Where material-related or process-related questions remain unresolved, a feasibility study can provide a basis for decision-making.
Would you like to assess whether an engine component can be repaired? Contact OSCAR PLT GmbH and tell us about the damage, material and installation conditions. Together, we can determine the next technical steps.
ProFocus is an intuitive, modular laser welding system that brings modern laser cladding into everyday production—enabling automated repair, coating and additive build-up of metal components with reduced material use, minimal rework, and stable, reproducible quality.
The compact version combines all the benefits of ProFocus technology in an innovative laser head whose efficient design enables completely new applications and geometries.
Turnkey laser cell for laser cladding, metal 3D printing, repair and coating of small to medium-sized components – compact, flexible and easy to use.
You are currently viewing a placeholder content from Brevo. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More InformationYou need to load content from reCAPTCHA to submit the form. Please note that doing so will share data with third-party providers.
More InformationYou need to load content from Turnstile to submit the form. Please note that doing so will share data with third-party providers.
More InformationYou are currently viewing a placeholder content from hCaptcha. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More InformationYou need to load content from reCAPTCHA to submit the form. Please note that doing so will share data with third-party providers.
More InformationYou are currently viewing a placeholder content from Turnstile. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More Information